The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
We have found the article about How to Install a Bathtub Yourself directly below on the net and believe it made perfect sense to relate it with you on this page.
Mounting a bath tub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably hard task. If the old bathtub is easily easily accessible, the project can relocate quickly; if you have to open up a wall surface to eliminate the old tub and also place the brand-new bathtub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. See to it you have certified yourself for the task and fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed project, it is better to take into consideration employing one prior to you start. Chances are you might need an expert plumber to make tube links.
This article will certainly help you set up a brand-new bath tub in your restroom if you have actually already acquired a new bathtub and also do not require to change the plan of your previous water supply pipes.
Your devices and material list need to comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Using the two wood boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by checking the spirit level as well as changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost flexible tap port to the suitable supply pipeline by making a compression join; then do the same for the other tap.
Switch on the water supply and check all joints as well as new pipework for leaks and tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub needs to wait till the tub has been made use of a minimum of when as this will certainly resolve it into its last position.
Planning for the Installation
First of all, the supporting framework provided with the bath must be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with wetness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can break relatively very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that piece of content was smart. Don't hesitate to take a moment to distribute this blog if you enjoyed reading it. Thanks so much for going through it.
Rapid response assured. Report this page